General DIN 11864 was first released 1998 and showed aseptic DIN connections with both long ends and short ends. From release 2006-01 of DIN 11864 it cover only connections with long ends. The versions with short end are moved to a new standard, DIN 11853.
The o-ring and it’s groove are exactly the same in both standards. In total there are 6 standards covering this assortment: DIN 11864-1, Threaded connections with long ends DIN 11864-2, Flange connections with long ends DIN 11864-3, Clamp connections with long ends DIN 11853-1, Threaded connections with short ends DIN 11853-2, Flange connections with short ends DIN 11853-3, Clamp connections with short ends Comments to below part numbers Screws and nuts are not included in flange versions.
Clamp ring is not included in clamp versions, there is just a reference to recommended clamp ring.
O-ring is not included below, it is found in chapter “Seals”.
O-rings
Description
Denomination
Part No
Add to cart
O-rings for DIN 11864/11853
Please see “Seals, O-rings for DIN 11864/11853”
Aseptic DIN 11864-1 threaded -> DIN 11866 series A / EN 10357 series A tubes
Description
Denomination
OD/IDxt
Ls
d5
c
O-ring
Part No
Add to cart
Welding liner long
“Bundstutzen” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
Liner 11864-1/A 13.0×1.5 1.4404
13/10×1.5
27
21.9
41
12×3.5
90520-9863
Liner 11864-1/A 19.0×1.5 1.4404
19/16×1.5
27
27.9
41
18×3.5
90520-9864
Liner 11864-1/A 23.0×1.5 1.4404
23/20×1.5
26
35.9
43
22×3.5
90520-9865
Liner 11864-1/A 29.0×1.5 1.4404
29/26×1.5
26
42.9
43
28×3.5
90520-9866
Liner 11864-1/A 35.0×1.5 1.4404
35/32×1.5
32
48.9
48
34×5
90520-9867
Liner 11864-1/A 41.0×1.5 1.4404
41/38×1.5
31
54.9
48
40×5
90520-9868
Liner 11864-1/A 53.0×1.5 1.4404
53/50×1.5
30
66.9
48
52×5
90520-9869
Liner 11864-1/A 70.0×2.0 1.4404
70/66×2.0
40
84.9
60
68×5
90520-9870
Liner 11864-1/A 85.0×2.0 1.4404
85/81×2.0
40
98.9
64
83×5
90520-9871
Liner 11864-1/A 104×2.0 1.4404
104/100×2.0
40
118.9
64
102×5
90520-9459
Welding male long
“Gewindestutzen”
ID surface: <0.8µm
Material: EN 1.4404
Use the DIN 11851 nut
Male p.11864-1/A 13.0×1.5 1.4404
13/10×1.5
27
Rd28x1/8
41
–
90520-9872
Male p.11864-1/A 19.0×1.5 1.4404
19/16×1.5
27
Rd34x1/8
41
–
90520-9873
Male p.11864-1/A 23.0×1.5 1.4404
23/20×1.5
26
Rd44x1/6
43
–
90520-9874
Male p.11864-1/A 29.0×1.5 1.4404
29/26×1.5
26
Rd52x1/6
43
–
90520-9875
Male p.11864-1/A 35.0×1.5 1.4404
35/32×1.5
32
Rd58x1/6
48
–
90520-9876
Male p.11864-1/A 41.0×1.5 1.4404
41/38×1.5
31
Rd65x1/6
48
–
90520-9877
Male p.11864-1/A 53.0×1.5 1.4404
53/50×1.5
30
Rd78x1/6
48
–
90520-9878
Male p.11864-1/A 70.0×2.0 1.4404
70/66×2.0
40
Rd95x1/6
60
–
90520-9879
Male p.11864-1/A 85.0×2.0 1.4404
85/81×2.0
40
Rd110x1/4
64
–
90520-9880
Male p.11864-1/A 104×2.0 1.4404
104/100×2.0
40
Rd130x1/4
64
–
90520-9454
Aseptic DIN 11853-1 threaded -> DIN 11866 series A / EN 10357 series A tubes
Description
Denomination
OD/IDxt
Ls
d5
O-ring
c
Part No
Add to cart
Welding liner short
“Bundstutzen” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
Liner 11853-1/A DN10 1.4404
13/10×1.5
5
21.9
12×3.5
17.0
90511-8988
Liner 11853-1/A DN15 1.4404
19/16×1.5
5
27.9
18×3.5
17.0
90511-8989
Liner 11853-1/A DN20 1.4404
23/20×1.5
5
35.9
22×3.5
18.0
90511-8990
Liner 11853-1/A DN25 1.4404
29/26×1.5
8
42.9
28×3.5
22.0
90511-8991
Liner 11853-1/A DN32 1.4404
35/32×1.5
10
48.9
34×5
25.0
90511-8992
Liner 11853-1/A DN40 1.4404
41/38×1.5
10
54.9
40×5
26.0
90511-8993
Liner 11853-1/A DN50 1.4404
53/50×1.5
13
66.9
52×5
30.0
90511-8994
Liner 11853-1/A DN65 1.4404
70/66×2.0
15
84.9
68×5
34.0
90511-8995
Liner 11853-1/A DN80 1.4404
85/81×2.0
15
98.9
83×5
38.0
90511-8996
Liner 11853-1/A DN100 1.4404
104/100×2.0
23
118.9
102×5
46.0
90511-8997
Welding male short
Semi bright
“Gewindestutzen”
ID surface: <0.8µm
Material: EN 1.4404
Use the DIN 11851 nut
Male p.11853-1/A DN10 1.4404
13/10×1.5
5
Rd28x1/8
–
19.0
90511-8998
Male p.11853-1/A DN15 1.4404
19/16×1.5
5
Rd34x1/8
–
19.0
90511-8999
Male p.11853-1/A DN20 1.4404
23/20×1.5
5
Rd44x1/6
–
21.0
90511-9000
Male p.11853-1/A DN25 1.4404
29/26×1.5
10
Rd52x1/6
–
26.0
90511-9001
Male p.11853-1/A DN32 1.4404
35/32×1.5
14
Rd58x1/6
–
30.0
90511-9002
Male p.11853-1/A DN40 1.4404
41/38×1.5
15
Rd65x1/6
–
31.0
90511-9003
Male p.11853-1/A DN50 1.4404
53/50×1.5
15
Rd78x1/6
–
31.0
90511-9004
Male p.11853-1/A DN65 1.4404
70/66×2.0
16
Rd95x1/6
–
36.0
90511-9005
Male p.11853-1/A DN80 1.4404
85/81×2.0
18
Rd110x1/4
–
42.0
90511-9006
Male p.11853-1/A DN100 1.4404
104/100×2.0
26
Rd130x1/4
–
50.0
90511-9007
Blinds for DIN 11864-1 / DIN 11853-1 -> DIN 11866 series A / EN 10357 series A tubes
Description
Denomination
d5
h
O-ring
SW
Part No
Add to cart
Blind liner
“Bundstutzen” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
Blank liner 11864/11853-1/A DN10 1.4404
21.9
9
12×3.5
–
90519-3691
Blank liner 11864/11853-1/A DN15 1.4404
27.9
9
18×3.5
–
90519-3692
Blank liner 11864/11853-1/A DN20 1.4404
35.9
10
22×3.5
–
90519-3693
Blank liner 11864/11853-1/A DN25 1.4404
42.9
12
28×3.5
–
90519-3694
Blank liner 11864/11853-1/A DN32 1.4404
48.9
13
34×5
–
90519-3695
Blank liner 11864/11853-1/A DN40 1.4404
54.9
13
40×5
–
90606-3400
Blank liner 11864/11853-1/A DN50 1.4404
66.9
14
52×5
–
90606-3399
Blank liner 11864/11853-1/A DN65 1.4404
84.9
16
68×5
–
90606-3398
Blank liner 11864/11853-1/A DN80 1.4404
98.9
16
83×5
–
90606-3397
Blank liner 11864/11853-1/A DN100 1.4404
118.9
20
102×5
–
90606-3396
Blind male part
“Gewindestutzen”
ID surface: <0.8µm
Material: EN 1.4404
Blank m. p. 11864/11853-1/A DN10 1.4404
Rd 28×1/8
24
–
17
90519-3696
Blank m. p. 11864/11853-1/A DN15 1.4404
Rd 34×1/8
24
–
17
90519-3697
Blank m. p. 11864/11853-1/A DN20 1.4404
Rd 44×1/6
24
–
17
90519-3698
Blank m. p. 11864/11853-1/A DN25 1.4404
Rd 52×1/6
24
–
27
90519-3699
Blank m. p. 11864/11853-1/A DN32 1.4404
Rd 58×1/6
24
–
27
90519-3700
Blank m. p. 11864/11853-1/A DN40 1.4404
Rd 65×1/6
24
–
27
90519-3701
Blank m. p. 11864/11853-1/A DN50 1.4404
Rd 78×1/6
24
–
27
90519-3702
Blank m. p. 11864/11853-1/A DN65 1.4404
Rd 95×1/6
28
–
32
90519-3703
Blank m. p. 11864/11853-1/A DN80 1.4404
Rd 110×1/4
28
–
32
90519-3704
Blank m. p. 11864/11853-1/A DN100 1.4404
Rd_130x1/4
30
–
32
90519-3705
Nut for DIN 11864-1 and DIN 11853-1
Description
Denomination
A
B
C
Part No
Add to cart
Nut
Semi bright
(Also fit DIN 11851 connections)
Material: EN 1.4301
DIN11851 DN10 1.4301
38.0
18.0
Rd28x1/8
90511-9008
DIN11851 DN15 1.4301
44.0
18.0
Rd34x1/8
90511-9009
DIN11851 DN20 1.4301
54.0
20.0
Rd44x1/6
90511-9010
DIN11851 DN25 1.4301
63.0
21.0
Rd52x1/6
90511-9011
DIN11851 DN32 1.4301
70.0
21.0
Rd58x1/6
90511-9012
DIN11851 DN40 1.4301
78.0
21.0
Rd65x1/6
90511-9013
DIN11851 DN50 1.4301
92.0
22.0
Rd78x1/6
90511-9014
DIN11851 DN65 1.4301
112.0
25.0
Rd95x1/6
90511-9015
DIN11851 DN80 1.4301
127.0
29.0
Rd110x1/4
90511-9016
DIN11851 DN100 1.4301
148.0
31.0
Rd130x1/4
90511-9017
Aseptic DIN 11864-2 flange -> DIN 11866 series A / EN 10357 series A tubes
Description
Denomination
ODxt
d5
d
h
dx
Ls
O-ring
Part No
Add to cart
Grooved flange long
“Nutflansch” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
Grooved fl. 11864-2/A DN10 1.4404
13×1.5
37
9
41.5
4xM8x30
26
12×3.5
90521-2565
Grooved fl. 11864-2/A DN15 1.4404
19×1.5
42
9
41.5
4xM8x30
26
18×3.5
90521-2566
Grooved fl. 11864-2/A DN20 1.4404
23×1.5
47
9
41.5
4xM8x30
26
22×3.5
90521-2567
Grooved fl. 11864-2/A DN25 1.4404
29×1.5
53
9
41.5
4xM8x30
26
28×3.5
90521-2568
Grooved fl. 11864-2/A DN32 1.4404
35×1.5
59
9
46.5
4xM8x30
31
34×5
90521-2569
Grooved fl. 11864-2/A DN40 1.4404
41×1.5
65
9
46.5
4xM8x30
31
40×5
90521-2570
Grooved fl. 11864-2/A DN50 1.4404
53×1.5
77
9
46.5
4xM8x30
31
52×5
90521-2571
Grooved fl. 11864-2/A DN65 1.4404
70×2.0
95
9
55.5
8xM8x30
42
68×5
90521-2572
Grooved fl. 11864-2/A DN80 1.4404
85×2.0
112
11
59.5
8xM10x35
42
83×5
90521-2573
Grooved fl. 11864-2/A DN100 1.4404
104×2.0
137
11
59.5
8xM10x40
42
102×5
90520-9138
Grooved fl. 11864-2/A DN125 1.4404
129×2.0
161
11
61.5
8xM10x40
42
127×5
90520-9885
Grooved fl. 11864-2/A DN150 1.4404
154×2.0
188
11
61.5
8xM10x40
40
152×5
90520-2995
Liner flange long
“Bundflansch”
ID surface: <0.8µm
Material: EN 1.4404
Liner fl. 11864-2/A DN10 1.4404
13×1.5
37
9
40
4xM8x30
26
–
90521-2556
Liner fl. 11864-2/A DN15 1.4404
19×1.5
42
9
40
4xM8x30
26
–
90521-2557
Liner fl. 11864-2/A DN20 1.4404
23×1.5
47
9
40
4xM8x30
26
–
90521-2558
Liner fl. 11864-2/A DN25 1.4404
29×1.5
53
9
40
4xM8x30
26
–
90521-2559
Liner fl. 11864-2/A DN32 1.4404
35×1.5
59
9
45
4xM8x30
31
–
90521-2560
Liner fl. 11864-2/A DN40 1.4404
41×1.5
65
9
45
4xM8x30
31
–
90521-2561
Liner fl. 11864-2/A DN50 1.4404
53×1.5
77
9
45
4xM8x30
31
–
90521-2562
Liner fl. 11864-2/A DN65 1.4404
70×2.0
95
9
54
8xM8x30
42
–
90521-2563
Liner fl. 11864-2/A DN80 1.4404
85×2.0
112
11
58
8xM10x35
42
–
90521-2564
Liner fl. 11864-2/A DN100 1.4404
104×2.0
137
11
58
8xM10x40
42
–
90512-5188
Liner fl. 11864-2/A DN125 1.4404
129×2.0
161
11
60
8xM10x40
42
–
90512-5189
Liner fl. 11864-2/A DN150 1.4404
154×2.0
188
14
60
8xM10x40
40
–
90512-5190
Aseptic DIN 11853-2 flange -> DIN 11866 series A / EN 10357 series A tubes
Description
Denomination
ODxt
h
d5
Ls
d
dx
O-ring
Part No
Add to cart
Grooved flange short
“Nutflansch” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
Grooved fl. 11853-2/A DN10 1.4404
13×1.5
25.5
37
10
9
4xM8x30
12×3.5
90521-4970
Grooved fl. 11853-2/A DN15 1.4404
19×1.5
25.5
42
10
9
4xM8x30
18×3.5
90521-4971
Grooved fl. 11853-2/A DN20 1.4404
23×1.5
25.5
47
10
9
4xM8x30
22×3.5
90521-4972
Grooved fl. 11853-2/A DN25 1.4404
29×1.5
25.5
53
10
9
4xM8x30
28×3.5
90521-4973
Grooved fl. 11853-2/A DN32 1.4404
35×1.5
25.5
59
10
9
4xM8x30
34×5
90521-4974
Grooved fl. 11853-2/A DN40 1.4404
41×1.5
25.5
65
10
9
4xM8x30
40×5
90521-4975
Grooved fl. 11853-2/A DN50 1.4404
53×1.5
25.5
77
10
9
4xM8x30
52×5
90521-4976
Grooved fl. 11853-2/A DN65 1.4404
70×2.0
25.5
95
10
9
8xM8x30
68×5
90521-4977
Grooved fl. 11853-2/A DN80 1.4404
85×2.0
27.5
112
10
11
8xM10x35
83×5
90521-4978
Grooved fl. 11853-2/A DN100 1.4404
104×2.0
27.5
137
10
11
8xM10x40
102×5
90511-9045
Grooved fl. 11853-2/A DN125 1.4404
129×2.0
29.5
161
10
11
8xM10x40
127×5
90511-9046
Grooved fl. 11853-2/A DN150 1.4404
154×2.0
29.5
188
8
14
8xM12x50
152×5
90511-9047
Liner flange
“Bundflansch”
ID surface: <0.8µm
Material: EN 1.4404
Liner fl. 11853-2/A DN10 1.4404
13×1.5
24
37
10
9
4xM8x30
–
90521-4961
Liner fl. 11853-2/A DN15 1.4404
19×1.5
24
42
10
9
4xM8x30
–
90521-4962
Liner fl. 11853-2/A DN20 1.4404
23×1.5
24
47
10
9
4xM8x30
–
90521-4963
Liner fl. 11853-2/A DN25 1.4404
29×1.5
24
53
10
9
4xM8x30
–
90521-4964
Liner fl. 11853-2/A DN32 1.4404
35×1.5
24
59
10
9
4xM8x30
–
90521-4965
Liner fl. 11853-2/A DN40 1.4404
41×1.5
24
65
10
9
4xM8x30
–
90521-4966
Liner fl. 11853-2/A DN50 1.4404
53×1.5
24
77
10
9
4xM8x30
–
90521-4967
Liner fl. 11853-2/A DN65 1.4404
70×2.0
24
95
10
9
8xM8x30
–
90521-4968
Liner fl. 11853-2/A DN80 1.4404
85×2.0
26
112
10
11
8xM10x35
–
90521-4969
Liner fl. 11853-2/A DN100 1.4404
104×2.0
26
137
10
11
8xM10x40
–
90511-9042
Liner fl. 11853-2/A DN125 1.4404
129×2.0
28
161
10
11
8xM10x40
–
90511-9043
Liner fl. 11853-2/A DN150 1.4404
154×2.0
28
188
8
14
8xM12x50
–
90511-9044
Blinds for DIN 11864-2 / DIN 11853-2 -> DIN 11866 series A / EN 10357 series A tubes
Description
Denomination
d5
h
O-ring
Part No
Add to cart
Blind flange liner with groove
“Nutflansch” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
Bl.fl.w.gr. 11864/11853-2/A DN10 1.4404
37
11.5
12×3.5
90521-2574
Bl.fl.w.gr. 11864/11853-2/A DN15 1.4404
42
11.5
18×3.5
90521-2575
Bl.fl.w.gr. 11864/11853-2/A DN20 1.4404
47
11.5
22×3.5
90521-2576
Bl.fl.w.gr. 11864/11853-2/A DN25 1.4404
53
11.5
28×3.5
90521-2577
Bl.fl.w.gr. 11864/11853-2/A DN32 1.4404
59
11.5
34×5
90521-2578
Bl.fl.w.gr. 11864/11853-2/A DN40 1.4404
65
11.5
40×5
90521-2579
Bl.fl.w.gr. 11864/11853-2/A DN50 1.4404
77
11.5
52×5
90521-2580
Bl.fl.w.gr. 11864/11853-2/A DN65 1.4404
95
11.5
68×5
90521-2581
Bl.fl.w.gr. 11864/11853-2/A DN80 1.4404
112
13.5
83×5
90521-2582
Bl.fl.w.gr. 11864/11853-2/A DN100 1.4404
137
15.5
102×5
90520-9882
Bl.fl.w.gr. 11864/11853-2/A DN125 1.4404
161
15.5
127×5
90520-9883
Bl.fl.w.gr. 11864/11853-2/A DN150 1.4404
188
17.5
152×5
90520-9884
Blind flange liner
“Bundflansch”
ID surface: <0.8µm
Material: EN 1.4404
Bl.fl.Liner 11864/11853-2/A DN10 1.4404
37
10
–
90521-2583
Bl.fl.Liner 11864/11853-2/A DN15 1.4404
42
10
–
90521-2584
Bl.fl.Liner 11864/11853-2/A DN20 1.4404
47
10
–
90521-2585
Bl.fl.Liner 11864/11853-2/A DN25 1.4404
53
10
–
90521-2586
Bl.fl.Liner 11864/11853-2/A DN32 1.4404
59
10
–
90521-2587
Bl.fl.Liner 11864/11853-2/A DN40 1.4404
65
10
–
90521-2588
Bl.fl.Liner 11864/11853-2/A DN50 1.4404
77
10
–
90521-2589
Bl.fl.Liner 11864/11853-2/A DN65 1.4404
95
10
–
90521-2590
Bl.fl.Liner 11864/11853-2/A DN80 1.4404
112
12
–
90521-2591
Bl.fl.liner 11864/11853-2/A DN100 1.4404
137
14
–
90520-9881
Bl.fl.liner 11864/11853-2/A DN125 1.4404
161
14
–
90518-8864
Bl.fl.liner 11864/11853-2/A DN150 1.4404
188
16
–
90520-3017
Aseptic DIN 11864-1 threaded -> DIN 11866 series C / BS 4825 tubes
Description
Denomination
ODxt
Ls
d5
c
O-ring
Part No
Add to cart
Welding liner long
“Bundstutzen” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
Liner 11864-1/A 1/2″ 1.4404 H3 long
12.7×1.65
27
21.9
39
12×3.5
90517-4450
Liner 11864-1/A 3/4″ 1.4404 H3 long
19.05×1.65
27
27.9
39
18×3.5
90517-4451
Liner 11864-1/A 1″ 1.4404 H3 long
25.4×1.65
26
42.9
40
24×3.5
90517-4452
Liner 11864-1/A 1-1/2″ 1.4404 H3 long
38.1×1.65
30
54.9
46.5
37×5
90517-4518
Liner 11864-1/A 2″ 1.4404 H3 long
50.8×1.65
30
66.9
47.5
50×5
90517-4519
Liner 11864-1/A 2-1/2″ 1.4404 H3 long
63.5×1.65
40
84.9
63
62×5
90517-4520
Liner 11864-1/A 3″ 1.4404 H3 long
76.2×1.65
40
98.9
61
75×5
90517-4521
Liner 11864-1/A 4″ 1.4404 H3 long
101.6×2.11
40
118.9
65
100×5
90517-4522
Welding male long
“Gewindestutzen”
ID surface: <0.8µm
Material: EN 1.4404
Use the DIN 11851 nut
Male p. 11864-1/A 1/2″ 1.4404 H3 long
12.7×1.65
27
Rd28x1/8
41
–
90517-4434
Male p. 11864-1/A 3/4″ 1.4404 H3 long
19.05×1.65
27
Rd34x1/8
41
–
90517-4435
Male p. 11864-1/A 1″ 1.4404 H3 long
25.4×1.65
26
Rd52x1/6
43
–
90517-4436
Male p. 11864-1/A 1-1/2″ 1.4404 H3 long
38.1×1.65
30
Rd65x1/6
48.5
–
90517-4437
Male p. 11864-1/A 2″ 1.4404 H3 long
50.8×1.65
30
Rd78x1/6
48.5
–
90517-4438
Male p. 11864-1/A 2-1/2″ 1.4404 H3 long
63.5×1.65
40
Rd95x1/6
60
–
90517-4439
Male p. 11864-1/A 3″ 1.4404 H3 long
76.2×1.65
40
Rd110x1/4
64
–
90517-4440
Male p. 11864-1/A 4″ 1.4404 H3 long
101.6×2.11
40
Rd130x1/4
64
–
90517-4441
Aseptic DIN 11853-1 threaded -> DIN 11866 series C / BS 4825 tubes
Description
Denomination
ODxt
Ls
d5
c
O-ring
Part No
Add to cart
Welding liner short
“Bundstutzen” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
Liner 11853-1/A 1/2″ 12.7×1.65 short
12.7×1.65
6.5
21.9
17
12×3.5
90517-4555
Liner 11853-1/A 3/4″ 19.05×1.65 short
19.05×1.65
6.5
27.9
17
18×3.5
90517-4556
Liner 11853-1/A 1″ 25.4×1.65 short
25.4×1.65
8
42.9
22
24×3.5
90517-4557
Liner 11853-1/A 1-1/2″ 38.1×1.65 short
38.1×1.65
9.5
54.9
26
37×5
90517-4558
Liner 11853-1/A 2″ 50.8×1.65 short
50.8×1.65
12.5
66.9
30
50×5
90517-4559
Liner 11853-1/A 2-1/2″ 63.5×1.65 short
63.5×1.65
21
84.9
34
62×5
90517-4560
Liner 11853-1/A 3″ 76.2×1.65 short
76.2×1.65
17
98.9
38
75×5
90517-4561
Liner 11853-1/A 4″ 101.6×2.11 short
101.6×2.11
21
118.9
46
100×5
90517-4562
Welding male short
“Gewindestutzen”
ID surface: <0.8µm
Material: EN 1.4404
Use the DIN 11851 nut
Male p. 11853-1/A 1/2″ 1.4404 H3 short
12.7×1.65
5
Rd28x1/8
19
–
90517-4442
Male p. 11853-1/A 3/4″ 1.4404 H3 short
19.05×1.65
5
Rd34x1/8
19
–
90517-4443
Male p. 11853-1/A 1″ 1.4404 H3 short
25.4×1.65
10
Rd52x1/6
26
–
90517-4444
Male p. 11853-1/A 1-1/2″ 1.4404 H3 short
38.1×1.65
15
Rd65x1/6
31
–
90517-4445
Male p. 11853-1/A 2″ 1.4404 H3 short
50.8×1.65
15
Rd78x1/6
31
–
90517-4446
Male p. 11853-1/A 2-1/2″ 1.4404 H3 short
63.5×1.65
18
Rd95x1/6
36
–
90517-4447
Male p. 11853-1/A 3″ 1.4404 H3 short
76.2×1.65
18
Rd110x1/4
42
–
90517-4448
Male p. 11853-1/A 4″ 1.4404 H3 short
101.6×2.11
26
Rd130x1/4
50
–
90517-4449
Blinds for DIN 11864-1 / DIN 11853-1 -> DIN 11866 series C / BS 4825 tubes
Description
Denomination
d5
h
O-ring
SW
Part No
Add to cart
Blind liner
“Bundstutzen” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
Blank liner 11864/11853-1/A 0.5″ 1.4404
21.9
9
12×3.5
–
90517-4539
Blank liner 11864/11853-1/A 0.75″ 1.4404
27.9
9
18×3.5
–
90517-4540
Blank liner 11864/11853-1/A 1″ 1.4404
42.9
12
24×3.5
–
90517-4541
Blank liner 11864/11853-1/A 1.5″ 1.4404
54.9
13
37×5
–
90517-4542
Blank liner 11864/11853-1/A 2″ 1.4404
66.9
14
50×5
–
90517-4543
Blank liner 11864/11853-1/A 2.5″ 1.4404
84.9
16
62×5
–
90517-4544
Blank liner 11864/11853-1/A 3″ 1.4404
98.9
16
75×5
–
90517-4545
Blank liner 11864/11853-1/A 4″ 1.4404
118.9
20
100×5
–
90517-4546
Blind male part
“Gewindestutzen”
ID surface: <0.8µm
Material: EN 1.4404
Blank m. p. 11864/11853-1/A 0.5″ 1.4404
Rd28x1/8
24
–
17
90517-4547
Blank m. p. 11864/11853-1/A 0.75″ 1.4404
Rd34x1/8
24
–
17
90517-4548
Blank m. p. 11864/11853-1/A 1″ 1.4404
Rd52x1/6
24
–
27
90517-4549
Blank m. p. 11864/11853-1/A 1.5″ 1.4404
Rd65x1/6
24
–
27
90517-4550
Blank m. p. 11864/11853-1/A 2″ 1.4404
Rd78x1/6
24
–
27
90517-4551
Blank m. p. 11864/11853-1/A 2.5″ 1.4404
Rd95x1/6
28
–
32
90517-4552
Blank m. p. 11864/11853-1/A 3″ 1.4404
Rd110x1/4
28
–
32
90517-4553
Blank m. p. 11864/11853-1/A 4″ 1.4404
Rd130x1/4
30
–
32
90517-4554
Aseptic DIN 11864-2 flange -> DIN 11866 series C / BS 4825 tubes
Description
Denomination
ODxt
d5
d
h
dx
Ls
O-ring
Part No
Add to cart
Grooved flange long
“Nutflansch” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
Gr. flange 11864-2/A 1/2″ 1.4404
12.7×1.65
37
9
40
4xM8x30
26
12×3.5
90517-4523
Gr. flange 11864-2/A 3/4″ 1.4404
19.05×1.65
42
9
40
4xM8x30
26
18×3.5
90517-4524
Gr. flange 11864-2/A 1″ 1.4404
25.4×1.65
49
9
40
4xM8x30
26
24×3.5
90517-4525
Gr. flange 11864-2/A 1-1/2″ 1.4404
38.1×1.65
62
9
45
4xM8x30
31
37×3.5
90517-4526
Gr. flange 11864-2/A 2″ 1.4404
50.8×1.65
75
9
45
4xM8x30
31
50×5
90517-4527
Gr. flange 11864-2/A 2-1/2″ 1.4404
63.5×1.65
89
9
54
8xM8x30
42
62×5
90517-4528
Gr. flange 11864-2/A 3″ 1.4404
76.2×1.65
104
11
56
8xM10x30
42
75×5
90517-4529
Gr. flange 11864-2/A 4″ 1.4404
101.6×2.11
135
11
58
8xM10x35
42
100×5
90517-4530
Liner flange long
“Bundflansch”
ID surface: <0.8µm
Material: EN 1.4404
Liner flange11864-2/A 1/2″ 1.4404
12.7×1.65
37
9
41.5
4xM8x30
26
–
90517-4531
Liner flange11864-2/A 3/4″ 1.4404
19.05×1.65
42
9
41.5
4xM8x30
26
–
90517-4532
Liner flange11864-2/A 1″ 1.4404
25.4×1.65
49
9
41.5
4xM8x30
26
–
90517-4533
Liner flange11864-2/A 1-1/2″ 1.4404
38.1×1.65
62
9
46.5
4xM8x30
31
–
90517-4534
Liner flange11864-2/A 2″ 1.4404
50.8×1.65
75
9
46.5
4xM8x30
31
–
90517-4535
Liner flange11864-2/A 2-1/2″ 1.4404
63.5×1.65
89
9
55.5
4xM8x30
42
–
90517-4536
Liner flange11864-2/A 3″ 1.4404
76.2×1.65
104
11
57.5
8xM10x30
42
–
90517-4537
Liner flange11864-2/A 4″ 1.4404
101.6×2.11
135
11
59.5
8xM10x35
42
–
90517-4538
Blinds for DIN 11864-2 / DIN 11853-2 -> DIN 11866 series C / BS 4825 tubes
Description
Denomination
d5
h
O-ring
Part No
Add to cart
Blind flange liner with groove
Semi bright “Nutflansch” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
Bl.fl.w.gr. 11864/11853-2/A 4″ 1.4404
135
15.5
100×5
90520-8392
Blind flange liner
Semi bright “Bundflansch”
ID surface: <0.8µm
Material: EN 1.4404
Bl.fl.liner 11864/11853-2/A 4″ 1.4404
135
14
–
90520-8403
Aseptic DIN 11864-3 clamp -> DIN 11866 series C / BS 4825 tubes
Description
Denomination
ODxt
d10
L
Ls
O-ring
Rec. clamp
Part No
Add to cart
Clamp liner long with groove
“Bundstutzen” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
Rec. clamp not included
Cl. w. gr. 11864-3/A 1/2″ 1.4404
12.7×1.65
34
39.5
26
12×3.5
6_9611993113
90518-8745
Cl. w. gr. 11864-3/A 3/4″ 1.4404
19.05×1.65
34
39.5
26
18×3.5
6-9611993113
90518-8746
Cl. w. gr. 11864-3/A 1″ 1.4404
25.4×1.65
50.5
40
28
24×3.5
6-211053
90518-8747
Cl. w. gr. 11864-3/A 1-1/2″ 1.4404
38.1×1.65
64
45.5
30
37×5
6-211054
90518-8748
Cl. w. gr. 11864-3/A 2″ 1.4404
50.8×1.65
77.5
46
30
50×5
6-211055
90518-8749
Cl. w. gr. 11864-3/A 2-1/2″ 1.4404
63.5×1.65
91
59
40
62×5
6-211056
90518-8750
Cl. w. gr. 11864-3/A 3″ 1.4404
76.2×1.65
106
60
40
75×5
6-9611993114
90518-8751
Cl. w. gr. 11864-3/A 4″ 1.4404
101.6×2.11
130
61
40
100×5
6-9611994192
90518-8752
Clamp liner long
ID surface: <0.8µm
Material: EN 1.4404
Clamp liner 11864-3/A 1/2″ 1.4404
12.7×1.65
34
38
26
–
–
90518-8753
Clamp liner 11864-3/A 3/4″ 1.4404
19.05×1.65
34
38
26
–
–
90518-8754
Clamp liner 11864-3/A 1″ 1.4404
25.4×1.65
50.5
38.5
28
–
–
90518-8755
Clamp liner 11864-3/A 1-1/2″ 1.4404
38.1×1.65
64
44
30
–
–
90518-8756
Clamp liner 11864-3/A 2″ 1.4404
50.8×1.65
77.5
44.5
30
–
–
90518-8757
Clamp liner 11864-3/A 2-1/2″ 1.4404
63.5×1.65
91
57.5
40
–
–
90518-8928
Clamp liner 11864-3/A 3″ 1.4404
76.2×1.65
106
58.5
40
–
–
90518-8929
Clamp liner 11864-3/A 4″ 1.4404
101.6×2.11
130
59.5
40
–
–
90518-8930
Aseptic DIN 11853-3 clamp -> DIN 11866 series C / BS 4825 tubes
Description
Denomination
ODxt
d10
L
Ls
O-ring
Rec. clamp
Part No
Add to cart
Clamp liner short with groove
“Bundstutzen” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
Cl. w. gr. 11853-3/A 1/2″ 1.4404
12.7×1.65
34
23.5
10
12×3.5
6_9611993113
90517-9192
Cl. w. gr. 11853-3/A 3/4″ 1.4404
19.05×1.65
34
23.5
10
18×3.5
6_9611993113
90517-9193
Cl. w. gr. 11853-3/A 1″ 1.4404
25.4×1.65
50.5
23.5
10
24×3.5
6-211053
90517-9194
Cl. w. gr. 11853-3/A 1 1/2″ 1.4404
38.1×1.65
64
25.5
10
37×5
6-211054
90517-9195
Cl. w. gr. 11853-3/A 2″ 1.4404
50.8×1.65
77.5
26
10
50×5
6-211055
90517-9196
Cl. w. gr. 11853-3/A 2 1/2″ 1.4404
63.5×1.65
91
29
10
62×5
6-211056
90517-9197
Cl. w. gr. 11853-3/A 3″ 1.4404
76.2×1.65
106
30
10
75×5
6-9611993114
90517-9198
Cl. w. gr. 11853-3/A 4″ 1.4404
101.6×2.11
130
31
10
100×5
6-9611994192
90517-9199
Clamp liner short
ID surface: <0.8µm
Material: EN 1.4404
Mô tả
DIN 11864 was first released 1998 and showed aseptic DIN connections with both long ends and short ends. From release 2006-01 of DIN 11864 it cover only connections with long ends. The versions with short end are moved to a new standard, DIN 11853.
The o-ring and it’s groove are exactly the same in both standards.
In total there are 6 standards covering this assortment:
DIN 11864-1, Threaded connections with long ends
DIN 11864-2, Flange connections with long ends
DIN 11864-3, Clamp connections with long ends
DIN 11853-1, Threaded connections with short ends
DIN 11853-2, Flange connections with short ends
DIN 11853-3, Clamp connections with short ends
Comments to below part numbers
Screws and nuts are not included in flange versions.
Clamp ring is not included in clamp versions, there is just a reference to recommended clamp ring.
O-ring is not included below, it is found in chapter “Seals”.
Please see “Seals, O-rings for DIN 11864/11853”
“Bundstutzen” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
“Gewindestutzen”
ID surface: <0.8µm
Material: EN 1.4404
Use the DIN 11851 nut
“Bundstutzen” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
Semi bright
“Gewindestutzen”
ID surface: <0.8µm
Material: EN 1.4404
Use the DIN 11851 nut
“Bundstutzen” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
“Gewindestutzen”
ID surface: <0.8µm
Material: EN 1.4404
Semi bright
(Also fit DIN 11851 connections)
Material: EN 1.4301
“Nutflansch” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
“Bundflansch”
ID surface: <0.8µm
Material: EN 1.4404
“Nutflansch” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
“Bundflansch”
ID surface: <0.8µm
Material: EN 1.4404
“Nutflansch” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
“Bundflansch”
ID surface: <0.8µm
Material: EN 1.4404
“Bundstutzen” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
“Gewindestutzen”
ID surface: <0.8µm
Material: EN 1.4404
Use the DIN 11851 nut
“Bundstutzen” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
“Gewindestutzen”
ID surface: <0.8µm
Material: EN 1.4404
Use the DIN 11851 nut
“Bundstutzen” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
“Gewindestutzen”
ID surface: <0.8µm
Material: EN 1.4404
“Nutflansch” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
“Bundflansch”
ID surface: <0.8µm
Material: EN 1.4404
Semi bright “Nutflansch” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
Semi bright “Bundflansch”
ID surface: <0.8µm
Material: EN 1.4404
“Bundstutzen” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
Rec. clamp not included
ID surface: <0.8µm
Material: EN 1.4404
“Bundstutzen” with groove for o-ring type “Form A”
ID surface: <0.8µm
Material: EN 1.4404
O-ring not included
ID surface: <0.8µm
Material: EN 1.4404